Livnitup

If you gave them the values on the common tab spreadsheet then they probably have the same values. Any Platinum should've had 740/41-03-01 A000 xx originally on DDM/PDM and would've had 740/41-12-01 00xx.

khsonic03

This is probably a longshot, but do you think it's possible to do a one-touch full open/close of the sunroof shade? I hate that I have to press the button, wait for it to open halfway then press it again to open it all the way.

fordtrk

Prob will have to change the switch like the auto open windows have. The switch probably only works as you are pressing it (momentary) instead of pressing once to turn on.

B-ManFX4

If you go to Post # 2261 in this thread, there is a discussion about your exact problem and how it was resolved.

For Sync 3, try this: 7D0-01-01 AA2A-0x03-22xx

For Sync 2 this is what worked for me: 7D0-01-01 AA2A-0103-A6XX

If you would update your profile it would help people determine how best to assist you when you ask for help.

Airborne_Ape

Not necessarily.

there is a procedure to teach the truck moon roof operation by pressing the map lights 9 times in a specific order. It may be possible to try and 'break' the learning code and teach the truck that it has something it shouldn't.

I doubt there is anything in ForScan.

I don't recall any moon roof roof module. I wonder if the extended cab F150 has a motorized sun shade for the single panel moon roof. If it exists than maybe, just maybe, the sun shade can be taught different open commands.

....I'm not wearing my glasses, so my apologies.



This is all I know about moon roof calibration:


NOTE: The roof opening panel motor must be initialized when repairs are carried out on the roof opening panel system, including: any time the roof opening panel motor has been removed, the roof opening panel glass (fixed panoramic or front sliding) has been removed or adjusted, or if the roof opening panel frame has been removed.

NOTE: Initializing includes both the roof opening panel glass motor and the shield (sunhade) motor.

Place the roof opening panel sliding glass in the closed position.

With the driver’s door closed, place the ignition switch ON and wait for the overhead console lights to turn off.

NOTE: Steps 3 - 5 are to set up the overhead console to accept roof opening panel switch inputs to be held for up to a maximum of 150 seconds. Normally, the overhead console will consider the switch stuck after 30 seconds and ignore those longer inputs from the switch.


Steps 3 - 4 must be performed within 3 seconds.

Press the left map light once.

Press the right map light 4 times.

Press the left map light once.

NOTE: Step 7 must begin within 2 seconds of releasing the switch at the end of step 6.

Press and hold the roof opening panel sliding glass close switch until the roof opening panel glass moves to the closed (hard stop) and then the vent position, and the shield fully opens, then release the switch.

Press and hold the roof opening panel sliding glass close switch again until the roof opening panel sliding glass fully opens and closes and then the shield fully closes.

Release the switch and verify proper operation.

Arcticfox

I tried to run a search to see if this had already been mentioned but my manual states that there is a boost gauge available for vehicles that have ecoboost engines on the cluster display. Has any seen that this can be unlocked?

robbieg

You can turn it on, check post #1225

cwcb08

Only if he has a 8" cluster tho right? Unless I missed the post for a 4"?

go3go3go

In my 2015 once you shifted to D from R the camera would automatically switch to the front view. This was very helpful after backing out of a spot then having to make a full turn to miss the car that was parked next to you. The front camera gave a great view of how close you are getting to that car's bumper.

My 2016 does not automatically switch from the rear to front when shifting into Drive. I SURE MISS THAT!!!

Could someone here that has a 2015 model see if its in the code so we could program that feature into our 2016s with 360 cameras?

fordtrk

Cool I guess the switch/hardware is installed and compatible, Thanks for the correction.