Ford F150 Forum - Community of Ford Truck Fans

Topic Sponsor
2015 - 2020 Ford F150 General discussion on the 13th generation Ford F150 truck.
Sponsored by:
Sponsored by:

FORScan - software to enable/disable features in your truck

Thread Tools
 
Search this Thread
 
Old 01-14-2017, 10:45 PM
  #5421  
Junior Member
 
hhowell1990's Avatar
 
Join Date: Jan 2017
Posts: 24
Likes: 0
Received 1 Like on 1 Post

Default
Originally Posted by Figg
hhowell, did you try these as well?

726-27-01 x*xx xxxx xxxx Front bulb turn outage cfg: 1=outage, 0=no outage
726-27-01 xxx* xxxx xxxx Front LED turn outage cfg: 0=no outage, 1=outage
i will try them in the morning
hhowell1990 is offline  
Reply Like
Old 01-14-2017, 10:54 PM
  #5422  
The FORScan Guy

Thread Starter
 
Livnitup's Avatar
 
Join Date: Dec 2015
Location: SoCal
Posts: 5,777
Received 4,919 Likes on 1,995 Posts

Default
Originally Posted by Livnitup
Yeah, I realize that and it's like I said above. If you pm me your VIN we might be able to get to the bottom of it.
So after pulling up your VIN's as-built, your values are the same as mine with LEDs and I'm using this and don't have the hyperflash of turn signals on dash:
726-27-01 0001 0000 01xx

All I can suggest is double check what you wrote the first time.
Livnitup is offline  
Reply Like
Old 01-14-2017, 11:11 PM
  #5423  
The Source
 
DanMc85's Avatar
 
Join Date: Jul 2016
Location: New England, USA
Posts: 403
Received 247 Likes on 123 Posts

Default
Originally Posted by Csantos
Did anybody encounter this DTC's on Forscan? They keep coming back.
U3000 are permanent DTCs. You cannot erase them with normal tools.
DanMc85 is offline  
Reply Like
The following users liked this post:
Csantos (01-15-2017)
Old 01-15-2017, 12:30 PM
  #5424  
Senior Member
 
nickers1952's Avatar
 
Join Date: May 2016
Location: Austin, Texas
Posts: 117
Received 21 Likes on 13 Posts

Default
Is there a module that affects the side mirror spot light operation other than the 726-56-01 address in the BCM? I tried the jumper mod to have the spots operate at all speeds and now the spots don't work at all. I also tried flsdiver suggestion to reset the BCM module. This is my original post in the "Run the spotlights whenever you want" thread- Thx

Need a little help! I did this mod today and all went well... until I tried to use the spots - nothing. They worked last night, but after the mod, they don't. Fuse #16 is good and I have 12volts to pin 1. Put everything back to factory and still no spotlights. All the other light functions appear to be normal. I'm going to try a "reset" tomorrow (remove negative battery cable). I was careful not to short any of the pins to each other during the mod process. Anyone have any suggestions?? Thx
nickers1952 is offline  
Reply Like
Old 01-15-2017, 12:35 PM
  #5425  
The FORScan Guy

Thread Starter
 
Livnitup's Avatar
 
Join Date: Dec 2015
Location: SoCal
Posts: 5,777
Received 4,919 Likes on 1,995 Posts

Default
Originally Posted by nickers1952
Is there a module that affects the side mirror spot light operation other than the 726-56-01 address in the BCM? I tried the jumper mod to have the spots operate at all speeds and now the spots don't work at all. I also tried flsdiver suggestion to reset the BCM module. This is my original post in the "Run the spotlights whenever you want" thread- Thx
Other than the BCM value you referenced above, there is no other value that controls/affects the spot lights.
Livnitup is offline  
Reply Like
The following users liked this post:
nickers1952 (01-15-2017)
Old 01-15-2017, 12:42 PM
  #5426  
Senior Member
 
nickers1952's Avatar
 
Join Date: May 2016
Location: Austin, Texas
Posts: 117
Received 21 Likes on 13 Posts

Default
Originally Posted by Livnitup
Other than the BCM value you referenced above, there is no other value that controls/affects the spot lights.
Thanks - I was afraid of that... Don't know what I did, but it killed my spot's! Let the fun begin!
nickers1952 is offline  
Reply Like
Old 01-15-2017, 01:00 PM
  #5427  
Junior Member
 
hhowell1990's Avatar
 
Join Date: Jan 2017
Posts: 24
Likes: 0
Received 1 Like on 1 Post

Default
Originally Posted by Livnitup
So after pulling up your VIN's as-built, your values are the same as mine with LEDs and I'm using this and don't have the hyperflash of turn signals on dash:
726-27-01 0001 0000 01xx

All I can suggest is double check what you wrote the first time.
Just double checked and mine matches that but still getting the hyperflash on the dashboard
hhowell1990 is offline  
Reply Like
Old 01-15-2017, 01:01 PM
  #5428  
Senior Member
iTrader: (3)
 
Integlspwr's Avatar
 
Join Date: Nov 2015
Location: Buffalo, NY
Posts: 391
Received 25 Likes on 21 Posts
Default
Originally Posted by hhowell1990
Just double checked and mine matches that but still getting the hyperflash on the dashboard
i did that edit and have no hyper flash with no resistors with my oem led tail lights.
Integlspwr is offline  
Reply Like
Old 01-15-2017, 01:10 PM
  #5429  
Senior Member
 
digitaltrucker's Avatar
 
Join Date: Dec 2011
Location: Texas
Posts: 11,822
Received 2,311 Likes on 1,764 Posts

Default
Just for grins, disconnect the battery for 10 minutes.
digitaltrucker is online now  
Reply Like
Old 01-15-2017, 01:15 PM
  #5430  
Junior Member
 
hhowell1990's Avatar
 
Join Date: Jan 2017
Posts: 24
Likes: 0
Received 1 Like on 1 Post

Default
Originally Posted by digitaltrucker
Just for grins, disconnect the battery for 10 minutes.
just did that as a last ditch effort for it to hopefully correct itself.

Originally Posted by Integlspwr
i did that edit and have no hyper flash with no resistors with my oem led tail lights.
checked it 3 times just now and its set as the spreadsheet on the first page says it should be set.
hhowell1990 is offline  
Reply Like



Advanced Search
Quick Reply: FORScan - software to enable/disable features in your truck


Reply Closed Thread Share

All times are GMT -4. The time now is 06:27 PM.