FORScan - software to enable/disable features in your truck
04-30-2017, 08:58 AM
#8141
04-30-2017, 09:03 AM
#8142
Senior Member
If the problem wasn't caused by Forscan then yes they should. If ford always did the right thing and honored their warranty when they should then no they shouldn't be on the hook for it. Should Ford be on the hook cooled seats that don't work or for the BS denials of legitimate warranty claims? I'm a pretty honest guy and I try to do the right thing but I also believe in an eye for an eye, Ford won't get any sympathy from me.
The following 3 users liked this post by robbieg:
04-30-2017, 09:28 AM
#8143
Junior Member
Join Date: Jun 2012
Posts: 16
Likes: 0
Received 0 Likes
on
0 Posts
I did by accident while testing something. The audio amp decided it would not longer play the backup beep noise through the door speakers and instead the IPC took over with it's internal speaker, which sounds like every microwave oven ever. I reverted my settings in ForScan but the truck never went back to normal until I did a full power down and ignition restart.
Your issue may be separate, but you said you have no idea where to start. I'd start by going back on any recent ACM changes you might have made and leave the truck off for a while.
Also, when in it comes to computers, when in doubt, reboot.
Your issue may be separate, but you said you have no idea where to start. I'd start by going back on any recent ACM changes you might have made and leave the truck off for a while.
Also, when in it comes to computers, when in doubt, reboot.
04-30-2017, 10:41 AM
#8144
Senior Member
U2100:00 Initial Configuration Not
Complete: No Sub Type
Information
This DTC sets when the CCM configuration has not been
completed. CARRY OUT the PMI (when the original module is not
available) for the module in question as directed by the diagnostic
scan tool.
REFER to: Module Configuration - System Operation and
Component Description (418-01 Module Configuration, Description
and Operation).
04-30-2017, 10:52 AM
#8145
The FORScan Guy
Thread Starter
04-30-2017, 11:02 AM
#8146
The FORScan Guy
Thread Starter
U2100:00 Initial Configuration Not
Complete: No Sub Type
Information
This DTC sets when the CCM configuration has not been
completed. CARRY OUT the PMI (when the original module is not
available) for the module in question as directed by the diagnostic
scan tool.
REFER to: Module Configuration - System Operation and
Component Description (418-01 Module Configuration, Description
and Operation).
Complete: No Sub Type
Information
This DTC sets when the CCM configuration has not been
completed. CARRY OUT the PMI (when the original module is not
available) for the module in question as directed by the diagnostic
scan tool.
REFER to: Module Configuration - System Operation and
Component Description (418-01 Module Configuration, Description
and Operation).
Last edited by Livnitup; 04-30-2017 at 11:15 AM.
04-30-2017, 11:39 AM
#8147
The Source
Check 726-22-02 xxxx x*xx xxxx - if you have a 1 there and your as-built shows a 0, try writing 0 to it and then re-read the BCM and see if it actually wrote the 0 or it's back to 1 again. If it's back to 1 again you have the same permanent BCM DTC that a few of us have and there's no fixing it even with IDS (I've tried). If it's a 0 on the initial read DO NOT try writing a 1 there or it'll probably be permanent.
The only way to get rid of a permanent DTC is to basically have a firmware flash go bad to where the module doesn't work... and access the bootloader and reflash the module. It completely resets and deletes all permanent DTCs. I did that with my PAM module when a U3000 wouldn't go away.... I don't recommend it, I discovered it by mistake. Some modules may not be so forgiving with recovery.
Last edited by DanMc85; 04-30-2017 at 11:46 AM.
04-30-2017, 11:41 AM
#8148
The Source
04-30-2017, 11:43 AM
#8149
The Source
04-30-2017, 11:45 AM
#8150
The FORScan Guy
Thread Starter