FORScan - software to enable/disable features in your truck
06-06-2017, 10:54 PM
#8921
Senior Member
Originally Posted by Livnitup
726-22-02 xxx1 xxxx xxxx - Remote Start enabled
It seems to me that recently someone pm'd me that did a mod that caused the same thing though but at a different address and after resetting their BCM (wrench icon in FORScan) it was working again. If you have a 1 in the position above then leave this address alone because this is the address (2nd set of #'s) that may give you the pulsating courtesy lights.
Lookup your BCM as-built info here: http://motorcraftservice.com/AsBuilt with your VIN and undo all the addresses of the mods you did in BCM if the above doesn't work.
It seems to me that recently someone pm'd me that did a mod that caused the same thing though but at a different address and after resetting their BCM (wrench icon in FORScan) it was working again. If you have a 1 in the position above then leave this address alone because this is the address (2nd set of #'s) that may give you the pulsating courtesy lights.
Lookup your BCM as-built info here: http://motorcraftservice.com/AsBuilt with your VIN and undo all the addresses of the mods you did in BCM if the above doesn't work.
06-06-2017, 11:16 PM
#8922
Senior Member
06-07-2017, 06:07 AM
#8923
Senior Member
Unless of course you turned off the remote start in the as built data
Last edited by lucas8888; 06-07-2017 at 06:12 AM.
06-07-2017, 01:03 PM
#8924
Senior Member
Is there anyone local to central MD that is knowledgeable using FORScan. I would love to throw someone a few bucks if they could show me how to set my ANZO Day time running lights to be on all the time.
06-07-2017, 02:15 PM
#8925
Senior Member
I also read that if you do disconnect the battery, that you should do an idle relearn for the PCM to relearn the idle base line, or something. 2016BGG posted a youtube video on how to do it a while back. I do this now after I have disconnected my battery for something.
06-07-2017, 06:13 PM
#8926
Senior Member
The same has happened to me. Disconnecting the battery as described above corrects it for me.
I also read that if you do disconnect the battery, that you should do an idle relearn for the PCM to relearn the idle base line, or something. 2016BGG posted a youtube video on how to do it a while back. I do this now after I have disconnected my battery for something.
I also read that if you do disconnect the battery, that you should do an idle relearn for the PCM to relearn the idle base line, or something. 2016BGG posted a youtube video on how to do it a while back. I do this now after I have disconnected my battery for something.
The following users liked this post:
carrierj (06-07-2017)
06-07-2017, 10:57 PM
#8927
What does ABM stand for?
I get asked a lot via pm about bulb outage settings from guys doing upgrades so I thought I'd post all the know outage stuff here so I can reference it in the future:
BCM Module:
726-27-01 x*xx xxxx xxxx Front bulb turn outage cfg: 1=outage, 0=no outage
726-27-01 xxx* xxxx xxxx Front LED turn outage cfg: 0=no outage, 1=outage
726-27-02 xxx* xxxx xxxx Low Beam outage cfg: 1=outage, 0=no outage
726-27-02 xxxx x*xx xxxx Trailer outage: 1=outage, 0=no outage
726-27-02 xxxx xxxx x*xx Rear bulb turn outage cfg: 1=outage, 0=no outage
726-27-02 x*xx xxxx xxxx ABM outage cfg: 1=outage, 0=no outage
726-28-01 x*xx xxxx xxxx Rear LED turn outage cfg: 0=no outage, 1=outage
BCM Module:
726-27-01 x*xx xxxx xxxx Front bulb turn outage cfg: 1=outage, 0=no outage
726-27-01 xxx* xxxx xxxx Front LED turn outage cfg: 0=no outage, 1=outage
726-27-02 xxx* xxxx xxxx Low Beam outage cfg: 1=outage, 0=no outage
726-27-02 xxxx x*xx xxxx Trailer outage: 1=outage, 0=no outage
726-27-02 xxxx xxxx x*xx Rear bulb turn outage cfg: 1=outage, 0=no outage
726-27-02 x*xx xxxx xxxx ABM outage cfg: 1=outage, 0=no outage
726-28-01 x*xx xxxx xxxx Rear LED turn outage cfg: 0=no outage, 1=outage
06-08-2017, 02:25 AM
#8928
It's my first day
To all those who come here, read the thread and never post anything (Hi there countless Ford employees), thought I'd mention I'll be at Princess Auto in North Edmonton Saturday morning for a local Alberta F150 meet. I'll undoubtedly be programming a lot of different things for a whole bunch of people with ForScan if anyone here cares a swing by.
